To view this site, you must enable JavaScript or upgrade to a JavaScript-capable browser. SKU: KWxx. Quantity discounts available. Quantity Price. Add to Cart. More Products by Kwikset. SmartCode Electronic Locks With your own personal code, you can enter your home with just a few simple pushes of a button and lock it with just one.
Home Connect Technology Kwikset's Home Connect Technology allows your front door lock to talk to other things in your house, such as the security system, lighting, thermostat and entertainment system — all through wireless Zigbee. The Best Security Is Smart Security An established leader in lock technology, Kwikset is widely recognized for providing families security and peace of mind with high quality door locks and door hardware. Round corner standard.
Remove the battery case from interior assembly by lifting the case up and out and set aside, see figure 7. Important before proceeding: 1.
Refer to section Work with the door open away from jamb to avoid accidental lock out. Make sure the bolt of latch is in the extended locked position. Install Exterior Assembly. Insert cylinder into exterior assembly. With key in cylinder, rotate the torque blade to align with crank in latch.
Place assembly on door, threading the wire harness through adapter - if used and under the latch. Install Interior Mounting plate. Carefully angle the connector of the wire harness - through the center hole of the mounting plate, utilizing the notch hole to allow connector to pass through see figure 7. Important, once the connector has passed through the center hole, tuck the wire harness out of the way by pressing it into the notch hole as shown in figure 8.
Slide wires through the notch until mounting plate sits flush against door. Making sure that exterior assembly and cylinder are pressed flush against exterior door, insert mounting bolts and tighten. Check the vertical alignment for mounting plate and exterior assembly. See figure 9. Using the key, retract and extend the bolt a few times to test for smooth action.
If action feels rough, loosen screws and re-align the mounting plate and the exterior assembly. Note: Also see step 1-c for possible crank interference. Repeat as required. Attach the Connector to the Interior Assembly. Important Note: To prevent damage, always handle the wire harness with care. Align the connector smooth side up with the connector port of the interior assembly.
For easier orientation, view the alignment of connection from the top of the interior assembly. Once aligned, push the connector in firmly to connect. Top of Interior Assembly. Install Interior Assembly. Making sure wires are clear of pinching and wire harness is routed as shown, place the interior assembly on door, aligning torque blade inside the turnpiece shaft.
Route wires down - avoiding any excess bulge at curve, which could interfere with battery pack installation. Wire Harness. Once flush on door, Small insert and tighten small screws Screws Torque Blade to secure assembly onto the mounting plate.
Note: To aid insertion of screws, approach the screw holes with the screw loaded onto the screwdriver. Install batteries. Install 4 new AA Alkaline batteries. Install the new batteries as indicated in illustration. Make sure batteries lie flat in holder. For best performance, rechargeable batteries are not recommended. May explode or leak and cause personal injury.
Do not disturb the unit for approximately 20 seconds until the interior Green LED flashes followed by a beep. It is very important that this process is allowed to finish properly.
See example for turnpiece position for right hand door RHD and left hand door LHD when bolt is fully thrown locked and fully retracted unlocked. Programming a User Code. Programming the 1st user code. Press the program button on the interior unit once. Enter in 4 to 8 digit code onto the keypad. The bolt should retract to the unlocked position.
If it does not unlock, repeat steps a through c. Programming the 2nd user code. Press the program button on the interior unit twice. Interior LED Features. SmartCode User Selectable Settings. The panel of SmartCode feature switches are located to the right of the program button. These switches enable and ON disable the following SmartCode settings. Basically, the Assure Lock tech will open the lock when you get near your door, while the DoorSense will lock your door.
Other features include pairing with your Apple watch or voice assistant such as Alexa, Hey Google, and Airbnb. Lastly, the lock system comes with two physical keys. This way, you can use either the passcode or the physical key. Not only is it easier to remember a code rather than always making sure you have your keys, but you can also customize passcodes for different individuals.
With an electronic deadbolt, you can also control and monitor when the door has been unlocked, making it a safer alternative than regular locks. Start Here Blog. These days, many homeowners and landlords are making the switch to electronic locks. After all, having one installed can be a convenient alternative to carrying around your keys. Not only are they safe, but they are also convenient for the modern tech-savvy person. Buy on Amazon.
0コメント